Automotive FAQ – LED lighting

General Information

What is Lumen?

Specifies the overall visible light output of a light source, which is emitted in all directions.

What is Candela?

Specifies the luminous flux, which is emitted into a certain direction.

What is Lux?

It is the measurement unit of illumination intensity. It specifies the luminous flux, which is emitted on a certain surface. At 1 lux e.g. the human eye can easily read a book.

What is IP?

The IP Code classifies and rates the degree of protection provided against intrusion, dust, accidental contact, and water by mechanical casings and electrical enclosures.

What is ECE?

United Nations Economic Commision for Europe.

What is the Reference Number?

The reference number is a value that is related to the high beam headlight which is regulated in ECE R112. Every certified high beam headlight has a reference number marked on it either left or right to the E-mark sign. According to ECE R112 the sum of all reference numbers of high beam headlights attached to the car must not exceed a total of 100.

What is an E-Mark?

An E-Mark has to be put on a product if it fullfills at least one category of the ECE regulation. Example and explanation:

  • H: Halogen/LED
  • D: Xenon
  • C: Low beam
  • R: High beam
  • PL: Plastic lens
  • 2439: Approval number
  • Arrow left right: left- and right-hand driving
  • 30: Reference number
  • E4: Granted approval in Netherlands

NIGHT BREAKER LED

  • OSRAM’s first street-legal LED replacement lamps1
  • Up to 230% more brightness2
  • Up to 5 times more lifetime3

1 Approved H4-LED and H7-LED headlamp for various countries. Please check countries, vehicles, and conditions before purchase here.
2 compared to minimum ECE R112. On top with 50% less glare.
3 compared to halogen lamps

To be sure that you have bought an original OSRAM LED product, OSRAM offers its customers the so-called Trust Program. This makes it possible to identify counterfeits. Further details can be found here: The OSRAM Trust Program

The design of the OSRAM NIGHT BREAKER LED is characterised by its uniqueness in the combination of two functions - "heat dissipation" and "optimum reflector design" . The optics are rounded off by a compact lamp size for optimum fitting accuracy in the headlamp.

Furthermore, the lamps are vibration-resistant to impacts, for example due to uneven road surfaces.

Quality and performance make every OSRAM product an OSRAM original. Unfortunately, product piracy has reached a point where it is difficult to visually distinguish between original and counterfeit.

OSRAM has therefore integrated security features into the production process that allow you to authenticate your lamps online in two simple steps.

OSRAM offers a 4-year guarantee for all NIGHT BREAKER LED lamps. One extra year of guarantee can be secured if the NIGHT BREAKER LED lamps are purchased at and installed by a professional workshop. Find more info here.

Approval for the legal NIGHT BREAKER LED is a very complex process for each vehicle model. Therefore, no statement on a concrete time estimate is possible at the present time, we hope for your understanding. OSRAM is continuously working on further development.

Approval for the legal NIGHT BREAKER LED is a very complex process for each vehicle model. Therefore, no statement on a concrete time estimate is possible at this point in time, we hope for your understanding. OSRAM is continuously working on further developments. You can always find the current country and vehicle list here.

Approval in other European countries depends on the respective legal situation of the country and to what extent they accept the approval. OSRAM cannot make any generally valid statement in this regard. You can view the current list of approved countries here.

The sticker supplied in the packaging should be affixed in the engine compartment or on the back of the headlamp. Applying the sticker is not mandatory.

The sticker is to be applied in the engine compartment, the approval is not affected by this. In case you lost the sticker please contact OSRAM customer service.

For vehicles declared as officially approved by OSRAM, the complete light distribution has been verified according to ECE R112. For vehicles that are not declared as approved by OSRAM, installation and use in road traffic will result in the invalidation of the operating permit and the loss of insurance coverage.

No, the laws of the country in which the vehicle is registered also apply abroad. This means that a vehicle cannot be objected to in a country where it is not registered. Countries with left-hand traffic (e.g. Great Britain) are an exception. Here, the driver must switch back to halogen lamps, even if the vehicle is registered in the home country.

OSRAM does not assume that there will be any queries from testing organisations or the police. If this should be the case, the OSRAM customer service offers support.

The headlamp approval number can be found directly on the headlamp - either on front glass or on a sticker of the housing. You can find example pictures here. A matching approval number is mandatory for approval.

In most cases only low beam is approved. In some cases high beam is also approved. Please check the compatibility list for details.

Yes, we as manufacturer recommend that the headlights get adjusted in a workshop after the lamps have been installed.

In case of any questions, please refer to the installation manual and our tutorials. If you still need assistance, please contact the OSRAM customer service. Installation accessories may be required.

Adapter, Canbus and Caps are required to install and use the lamps individually within different cars. Please note: Only genuine OSRAM accessories in connection with the NIGHT BREAKER LED lamps are approved for street-legal use.

OSRAM offers its customers a vehicle list per country with a detailed overview of the respective vehicle models, the tested headlamps and the installation accessories required for them.

The Canbus variants cover different vehicle types.

The installation accessories offered by OSRAM have been tested in combination with LED lamps and headlamps by official testing authorities and are to be used exclusively to obtain road approval.

OSRAM has carried out and passed the necessary electromagnetic compatibility tests according to ECE R10.

No, the LEDriving SMART CANBUS developed by OSRAM also has electronics built in.

Yes, in these cases the rotated position of the lamp is correct for best performance.

TRUCKSTAR LED

  • OSRAM's first street-legal1 LED retrofit lamps for 24V Vehicles
  • Up to 230% more brightness2 and 6000K
  • Up to 5 times more lifetime3

1 Approved LED light source - only applies to the respective countries in which there is approval or to which an equivalent approval applies, and the vehicle models and light functions currently listed in the compatibility list. For more details see www.osram.com/nb-led.
2 In comparison to the minimum requirements of ECE R112, while the glare is below the maximum permissible values by up to 50%.
3 In comparison to traditional halogen lamps.

To be sure that you have bought an original OSRAM LED product, OSRAM offers its customers the so-called Trust Program. This makes it possible to identify counterfeits. Further details can be found here: The OSRAM Trust Program

The design of the TRUCKSTAR LED is characterised by its uniqueness in the combination of two functions - "heat dissipation" and "optimum reflector design" . The optics are rounded off by a compact lamp size for optimum fitting accuracy in the headlamp.

Furthermore, the lamps are vibration-resistant to impacts, for example due to uneven road surfaces.

Quality and performance make every OSRAM product an OSRAM original. Unfortunately, product piracy has reached a point where it is difficult to visually distinguish between original and counterfeit.

OSRAM has therefore integrated security features into the production process that allow you to authenticate your lamps online in two simple steps.

OSRAM offers a 4-year guarantee for all TRUCKSTAR LED lamps. One extra year of guarantee can be secured if the TRUCKSTAR LED lamps are purchased at and installed by a professional workshop. Find more info here.

Approval for the legal TRUCKSTAR LED is a very complex process for each vehicle model. Therefore, no statement on a concrete time estimate is possible at the present time, we hope for your understanding. OSRAM is continuously working on further development.

Approval for the legal TRUCKSTAR LED is a very complex process for each vehicle model. Therefore, no statement on a concrete time estimate is possible at this point in time, we hope for your understanding. OSRAM is continuously working on further developments. You can always find the current country and vehicle list here.

Approval in other European countries depends on the respective legal situation of the country and to what extent they accept the approval. OSRAM cannot make any generally valid statement in this regard. You can view the current list of approved countries here.

The sticker supplied in the packaging should be affixed in the engine compartment or on the back of the headlamp. Applying the sticker is not mandatory.

The sticker is to be applied to the rear of the headlamp in the engine compartment, the approval is not affected by this. In case you lost the sticker please contact OSRAM customer service.

For vehicles declared as officially approved by OSRAM, the complete light distribution has been verified according to ECE R112. For vehicles that are not declared as approved by OSRAM, installation and use in road traffic will result in the invalidation of the operating permit and the loss of insurance coverage.

No, the laws of the country in which the vehicle is registered also apply abroad. This means that a vehicle cannot be objected to in a country where it is not registered. Countries with left-hand traffic (e.g. Great Britain) are an exception. Here, the driver must switch back to halogen lamps, even if the vehicle is registered in the home country.

OSRAM does not assume that there will be any queries from testing organisations or the police. If this should be the case, the OSRAM customer service offers support.

The headlamp approval number can be found directly on the headlamp - either on front glass or on a sticker of the housing. You can find example pictures here. A matching approval number is mandatory for approval.

In most cases only low beam is approved. In some cases high beam is also approved. Please check the compatibility list for details.

Yes, we as manufacturer recommend that the headlights get adjusted in a workshop after the lamps have been installed.

In case of any questions, please refer to the installation manual and our tutorials. If you still need assistance, please contact the OSRAM customer service. Installation accessories may be required.

Adapter, Canbus and Caps are required to install and use the lamps individually within different cars. Please note: Only genuine OSRAM accessories in connection with the TRUCKSTAR LED lamps are approved for street-legal use.

OSRAM offers its customers a vehicle list per country with a detailed overview of the respective vehicle models, the tested headlamps and the installation accessories required for them.

The Canbus variants cover different vehicle types.

The installation accessories offered by OSRAM have been tested in combination with LED lamps and headlamps by official testing authorities and are to be used exclusively to obtain road approval.

OSRAM has carried out and passed the necessary electromagnetic compatibility tests according to ECE R10.

No, the LEDriving SMART CANBUS developed by OSRAM also has electronics built in.

Yes, in these cases the rotated position of the lamp is correct for best performance.

LEDriving replacement lamps: LED retrofits

LED lamps offer a multitude of advantages, including their distinctive cool white light, which gives cars a modern look. Thanks to their instant light output, they provide faster signals and thus enable drivers behind you to react faster. In addition, they are characterized by their long lifetime and high energy efficiency compared to conventional lamps.

All OSRAM LEDriving fog and signal lamps – as well as OSRAM LEDriving HL EASY lamps for high and low beam replacements – are plug-and-play solutions.

This makes installing these lamps as easy as it gets. OSRAM LEDriving HL BRIGHT and LEDriving HL INTENSE high and low beam replacement lamps can be easily installed with an adapter and/or caps. However, there are specific vehicle restrictions for them.

This problem only affects lamps from our LEDriving HL and LEDriving SL product ranges. Check the lamp’s polarity and its contacts for corrosion. If your LED lamp does not turn on, you probably need to:

  1. Remove the LED lamp from the housing.
  2. Rotate the lamp by 180°.
  3. Put it back in the housing.
  4. Make sure the LED is on.

For more information, please refer to the user instruction.

Due to their higher level of energy efficiency, LEDriving replacement lamps use significantly less power than traditional lamps. This lack of power consumption could be interpreted as a broken lamp by the body control unit. The LEDriving SMART CANBUS and LEDriving CANBUS CONTROL UNIT serve as a bypass of a vehicle’s lamp failure detection system when using a LEDriving replacement lamp without compromising on the lamp’s performance or lifetime. The control units are easily installed and suitable for most vehicle models with an automatic lamp failure detection system.

LED lamps are significantly more robust than conventional lamps and are therefore easy to handle. You only have to avoid touching the LED chips as they are heat-sensitive.

We offer dedicated solutions for fog ( LEDriving FL) as well as high and low beam ( LEDriving HL BRIGHT) application. While LEDriving HL BRIGHT have been designed for optimum performance in far-field application, LEDriving FL lamps are ideal for near-field application.

These products do not have ECE approval and must not be used on public roads in any exterior application. Public roads use leads to cancellation of operating license and loss of insurance coverage. Several countries forbid sale and use of these products. Please contact your local distributor for further information.

LEDriving HL replacement lamps are compatible with 12 V vehicles. LEDriving HL EASY lamps are compatible with cars and motorcycles, however, we also have a dedicated LEDriving HLM motorcycle portfolio and for 24 V, a dedicated truck portfolio: LEDriving HLT.

LEDriving HL high and low beam lamps are not equipped with an internal resistor due to the negative effect on the lamps’ performance and lifetime. Furthermore, additional resistors are not necessary for all car models or applications.

LEDriving HL high and low beam lamps do have limitations in terms of compatibility. Please consult our vehicle overview at www.osram.com/ledcheck to see if your LEDriving HL lamps are compatible with your vehicle.

Forward lighting:

  • High and low beam headlight
  • Fog light

Signal lighting:

  • Parking/marking light/position light
  • Indicator light
  • Door/side light
  • Tail light
  • Brake light
  • License plate light and more

Interior lighting:

  • Dome light
  • Reading light
  • Dashboard light
  • Glovebox light
  • Legroom light
  • Trunk light and more

In addition to the general advantages of LED lamps, LEDriving replacement lamps provide benefits that you only find at OSRAM:

  • OSRAM quality control
  • Longer lifetime thanks to optimized heat management systems
  • OSRAM guarantee*
  • Continuous high-performance light output
  • High color temperature & homogeneous light distribution
  • Perfect fit
  • Easy plug & play installation
  • Easy-to-reach customer service

* Refer to www.osram.com/am-guarantee for precise conditions.

LEDriving replacement lamps are available in different light colors. Check the end of the order reference number to identify the color version: - CW = Cool White (up to 6,500 K) - R = Red - YE= Amber

LED Driving Lights

Can I install the driving light by myself?

The driving ligths can be installed by a technically skilled person. We recommend that people with no training have the installation done by a service centre.

My driving light mist up on the inside. Is this normal and what can I do to prevent it?

Since moisture can get into driving lights while driving in rain or when using a high-pressure jet at a car wash, slight misting of the driving lights is not considered to be a quality defect. The driving lights may also mist up during transitional weather. This should normally disappear after a short time by circulating air. A frequent cause of misted car lights is incorrect use of high-pressure jets while washing the car. We therefore recommend never directing the water jet directly at a driving light and keeping a distance of at least 30 cm from the car.

Do I have to consider special mounting regulations?

According to ECE regulations products need to be installed pairwise (national legislation may differ). There are no special mounting regulations on width and heigth, for pure high beam products. For products with position light, special mounting regulations apply (see user manual).

Can I wire the driving light directly to the corresponding light function?

The driving lights are fully ECE compliant and can therefore be directly wired to the corresponding light function.

Are the driving lights covered by any EMC test?

Yes, the driving lights are covered by ECE R10.

LED Working Lights

Can I install the working light by myself?

The working ligths can be installed by a technically skilled person. We recommend that people with no training have the conversion done by a service centre.

My working light mist up on the inside. Is this normal and what can I do to prevent it?

Since moisture can get into working lights while driving in rain or when using a high-pressure jet at a car wash, slight misting of the working lights is not considered to be a quality defect. The working lights may also mist up during transitional weather. This should normally disappear after a short time by circulating air. A frequent cause of misted car lights is incorrect use of high-pressure jets while washing the car. We therefore recommend never directing the water jet directly at a working light and keeping a distance of at least 30 cm from the car.

Do I have to consider special mounting regulations?

No special mounting regulations apply.

How do I have to wire the working lights?

The working lights need to be installed with a separate switch, they must not be directly wired to a light function of the car.

Are the working lights covered by any EMC test?

Yes, the working lights are covered by ECE R10.

LEDriving headlights: Golf VII Editions

Is it legal to drive with the LEDriving headlights for VW Golf VII on public roads in Europe?

The LEDriving headlights for VW Golf VII are fully ECE compliant for a replacement of halogen and xenon Golf VII headlights. They are approved according to R6, R7, R 48, R87 and R112 and may therefore be legally installed and used in Europe. This does not include special requirements of individual countries on top of the standard ECE certification of the product.

Does any other conversion have to be done to the vehicle along with replacing the headlight?

Using our headlight means that no other conversion is necessary. You do not need to refit a headlight washer system or dimmer.

Can I replace the LEDriving headlights for VW Golf VII by myself?

The headlights can be replaced by a technically skilled person. Ideally, the spoiler should be disassembled by two people. We recommend that people with no training have the conversion done by a service centre.

Are any special tools required for the conversion?

No special tool is needed. All screws and fittings can be loosened using a Torx attachment, screwdriver, and spanner.

How can I take out the 10 pin fitting for the original headlight?

The fitting can be carefully levered out using a screwdriver.

Does the headlight need adjustment after installation?

The headlight light beam pattern must be checked by a service centre and adjusted if necessary.

Should I expect error messages in the on-board system after installation?

Replacing the headlights will not lead to error messages.

Additional 2 red wires are attached to the LEDriving headlights for VW Golf VII. Where do I connect these?

These wires must be connected to the positive terminal of the vehicle battery. Without connection, impaired function and error messages in the on-board computer may occur.

Do the headlights have a cornering light function?

The headlight does not have a cornering light function.

My headlights mist up on the inside. Is this normal and what can I do to prevent it?

Since moisture can get into headlights while driving in rain or when using a high-pressure jet at a car wash, slight misting of the headlights is not considered to be a quality defect. The headlights may also mist up during transitional weather. This should normally disappear after a short time by circulating air.

A frequent cause of misted car lights is incorrect use of high-pressure jets while washing the car. We therefore recommend never directing the water jet directly at a headlight and keeping a distance of at least 30 cm from the car.

Do the LEDriving headlights for VW Golf VII also work with customer-specific coding?

The LEDriving headlights for VW Golf VII electronics were designed and validated on vehicles with factory coding. OSRAM therefore cannot guarantee that the headlights will function correctly in vehicles with modified coding. We ask you to check and consider this before installing the headlights.

Can I install the LEDriving headlights for VW Golf VII in every VW Golf VII model?

The LEDriving® headlights for VW Golf VII were designed according to the European car model of VW Golf VII pre facelift (08/2012-2017). This means that local adaptions of the manufacturers may have an impact on the functionality of the LEDriving® headlights for VW Golf VII.

LEDHL103 versions are a replacement for the OEM halogen headlight, LEDHL104 versions are a replacement for OEM xenon with LED day time running lights headlight.

What is the difference between the three editions GTI, BLACK and CHROME of LEDriving headlights for VW Golf VII? Are there technical or only differences in terms of the design?

The only difference between the three versions BLACK, CHROME and GTI is the different bezel coating. From technical side all versions are identical.

Are there any differences of the LEDriving headlights for VW Golf VII due to right and left hand driving?

The LEDriving headlights for VW Golf VII were designed according to the European car model of VW. This means that local adaptions of the manufacturers may have an impact on the functionality of the LEDriving headlights for VW Golf VII. LEDriving headlights for VW Golf VII are not suitable for left-hand traffic.

Are the LEDriving headlights for VW Golf VII approved according to SAE and CCC?

The LEDriving headlights for VW Golf VII are not SAE and CCC compliant.

Do I need an additional approval document for the LEDriving headlights for VW Golf VII (e.g. ABE)?

No additional documents are needed (special legal country requirements not included). Nevertheless LEDriving headlights for VW Golf VII have ECE approval and we offer an official document. Please get in touch with the colleagues at automotive-service@osram.com.

LEDriving XENARC headlights: Golf VI Editions

Is it legal to drive with the LEDriving XENARC Golf VI headlight on public roads in Europe?

The LEDriving XENARC Golf VI headlights are fully ECE compliant for a replacement of halogen Golf VI headlights. They are approved according to R6, R7, R48, R87 and R98 and may therefore be legally installed and used in Europe. This does not include special requirements of individual countries on top of the standard ECE certification of the product.

Does any other conversion have to be done to the vehicle along with replacing the headlight?

Using our 25W XENARC technology means that no other conversion is necessary. You do not need to refit a headlight washer system or dimmer.

Can I replace the LEDriving XENARC Golf VI headlights by myself?

The headlights can be replaced by a technically skilled person. Ideally, the spoiler should be disassembled by two people. We recommend that people with no training have the conversion done by a service centre.

Are any special tools required for the conversion?

No special tool is needed. All screws and fittings can be loosened using a Torx attachment, screwdriver, and spanner.

How can I take out the 10 pin fitting for the original headlight?

The fitting can be carefully levered out using a screwdriver.

Does the headlight need adjustment after installation?

The headlight light beam pattern must be checked by a service centre and adjusted if necessary.

Should I expect error messages in the on-board system after installation?

Replacing the headlights will not lead to error messages.

Additional 2 red wires are attached to the LEDriving XENARC Golf VI. Where do I connect these?

These wires must be connected to the positive terminal of the vehicle battery. Without connection, impaired function and error messages in the on-board computer may occur.

Do the headlights have a cornering light function?

The headlight does not have a cornering light function.

My headlights mist up on the inside. Is this normal and what can I do to prevent it?

Since moisture can get into headlights while driving in rain or when using a high-pressure jet at a car wash, slight misting of the headlights is not considered to be a quality defect. The headlights may also mist up during transitional weather. This should normally disappear after a short time by circulating air.

A frequent cause of misted car lights is incorrect use of high-pressure jets while washing the car. We therefore recommend never directing the water jet directly at a headlight and keeping a distance of at least 30 cm from the car.

Do the LEDriving XENARC Golf VI headlights also work with customer-specific coding?

The LEDriving XENARC Golf VI headlight electronics were designed and validated on vehicles with factory coding. OSRAM therefore cannot guarantee that the headlights will function correctly in vehicles with modified coding. We ask you to check and consider this before installing the headlights.

Can I install the LEDriving XENARC Golf VI headlights in every VW Golf VI model?

The LEDriving XENARC Golf VI headlights were designed according to the European car model of VW. This means that local adaptions of the manufacturers may have an impact on the functionality of the LEDriving XENARC Golf VI headlights.

What is the difference between the three editions GTI, BLACK and CHROME of LEDriving XENARC Golf VI headlights? Are there technical or only differences in terms of the design?

The only difference between the three versions BLACK, CHROME and GTI is the different bezel coating. From technical side all versions are identical.

Are there any differences of the LEDriving XENARC Golf VI headlights due to right and left hand driving?

The LEDriving XENARC Golf VI headlights were designed according to the European car model of VW. This means that local adaptions of the manufacturers may have an impact on the functionality of the LEDriving XENARC Golf VI headlights. LEDriving XENARC Golf VI headlights are not suitable for left-hand traffic.

Are the LEDriving XENARC Golf VI headlights approved according to SAE and CCC?

The LEDriving XENARC Golf VI headlights are not SAE and CCC compliant.

Do I need an additional approval document for the LEDriving XENARC Golf VI headlights (e.g. ABE)?

No additional documents are needed (special legal country requirements not included). Nevertheless LEDriving XENARC Golf VI headlights have ECE approval and we offer an official document. Please get in touch with the colleagues at automotive-service@osram.com.

LEDriving XENARC headlights: Ford Focus 3

Is it legal to drive with the LEDriving XENARC headlights for Ford Focus 3 on public roads in Europe?

The LEDriving XENARC headlights for Ford Focus 3 are fully ECE compliant for a replacement of halogen Ford Focus 3 headlights. They are approved according to R6, R7, R 48, R87 and R112 and may therefore be legally installed and used in Europe. This does not include special requirements of individual countries on top of the standard ECE certification of the product.

Why do we need a separate connection to the fuse box?

The LEDriving XENARC headlights for Ford Focus 3 has a LED day time running light, which the halogen version of the Ford Focus 3 headlight doesn`t have, therefore we need to get the signal from the fuse box.

Can I replace the LEDriving XENARC headlights for Ford Focus 3 by myself?

The headlights can be replaced by a technically skilled person. Ideally, the spoiler should be disassembled by two people. We recommend that people with no training have the conversion done by a service centre.

Are any special tools required for the conversion?

No special tool is needed. All screws and fittings can be loosened using a Torx attachment, screwdriver, and spanner.

How can I take out the 10 pin fitting for the original headlight?

The fitting can be carefully levered out using a screwdriver.

Does the headlight need adjustment after installation?

The headlight light beam pattern must be checked by a service centre and adjusted if necessary.

Should I expect error messages in the on-board system after installation?

Replacing the headlights will not lead to error messages.

Additional 2 red wires are attached to the LEDriving XENARC headlights for Ford Focus 3. Where do I connect these?

These wires must be connected to the positive terminal of the vehicle battery. Without connection, impaired function and error messages in the on-board computer may occur.

Do the headlights have a cornering light function?

The headlight does not have a cornering light function.

My headlights mist up on the inside. Is this normal and what can I do to prevent it?

Since moisture can get into headlights while driving in rain or when using a high-pressure jet at a car wash, slight misting of the headlights is not considered to be a quality defect. The headlights may also mist up during transitional weather. This should normally disappear after a short time by circulating air.

A frequent cause of misted car lights is incorrect use of high-pressure jets while washing the car. We therefore recommend never directing the water jet directly at a headlight and keeping a distance of at least 30 cm from the car.

Do the LEDriving XENARC headlights for Ford Focus 3 also work with customer-specific coding?

The LEDriving XENARC headlights for Ford Focus 3 electronics were designed and validated on vehicles with factory coding. OSRAM therefore cannot guarantee that the headlights will function correctly in vehicles with modified coding. We ask you to check and consider this before installing the headlights.

Can I install the LEDriving XENARC headlights for Ford Focus 3 in every Ford Focus 3 model?

The LEDriving XENARC headlights for Ford Focus 3 were designed according to the European car model of Ford Focus. This means that local adaptions of the manufacturers may have an impact on the functionality of the LEDriving XENARC headlights for Ford Focus 3.

Are there any differences of the LEDriving XENARC headlights for Ford Focus 3 due to right and left hand driving?

The LEDriving XENARC headlights for Ford Focus 3 were designed according to the European car model of Ford Focus 3 (2010-11/2014). This means that local adaptions of the manufacturers may have an impact on the functionality of the LEDriving XENARC headlights for Ford Focus 3. LEDriving XENARC headlights for Ford Focus 3 are not suitable for right-hand traffic.

Are the LEDriving XENARC headlights for Ford Focus 3 approved according to SAE and CCC?

The LEDriving XENARC headlights for Ford Focus 3 are not SAE and CCC compliant.

Do I need an additional approval document for the LEDriving XENARC headlights for Ford Focus 3 (e.g. ABE)?

No additional documents are needed (special legal country requirements not included). Nevertheless LEDriving XENARC headlights for Ford Focus 3 have ECE approval and we offer an official document. Please get in touch with the colleagues at automotive-service@osram.com.

Is there a difference between Ford Focus 3 and Ford Focus MK3?

No, this is the same headlight generation.

LED warning lights: LEDguardian

LED reading lights: ONYX COPILOT

What is the difference between M-7 and L-7?

OSRAM sells two versions of the ONYX COPILOT: the M-7 and the L-7.

ONYX COPILOT M-7: fully mounted version for e.g. cabins of a truck. The lamp with 20 lm light output for a pleasently warm and glare-free light is powered via cigarette lighter and has a length of 37 cm. The M-7 version fits in all cigarette lighter sockets.

ONYX COPILOT L-7:The lamp with 20 lm light output for a pleasently warm and glare-free light has a plastic base for fixed connection. The length is 37 cm.

If you need further help, do not hesitate to contact our OSRAM Technical Customer Service (automotive-service@osram.com).

Is the product suitable for passenger cars (12 volt) and trucks (24 volt)?

Yes, the product is suitable for 12V and 24V.

Further questions?

Automotive Service

(EN/DE)
Mo. - Fr. from 8am - 4pm